This document contains in detail what are considered to be violations of the CAA and corresponding penalties for failure to obey and should be read in full before purchasing or installing this off-road or race use only product. Use on State and Federal Highways may be a violation of the EPA Clean Air Act. Most of the parts and services offered in this online catalog are for off-road use or competition use only. īy ordering this tune, you agree to assume all responsibility for assuring that it is to be used for off-road and/or competition use only and is not to be used on a vehicle that is registered for use on public roads nor highways.īecause U.S., Canadian, and other international, state or provincial laws and regulations may prohibit removal or modification of components that were installed on vehicles by Ford Motor Company to meet emission requirements or to comply with motor vehicle safety regulations applicable to vehicles manufactured for use on public roads, VMP wants you to know the following: Please note that this does NOT include VMP Custom Tuning - see VMP email tuning options by clicking HERE.
Preloaded with SCT tune files for limited vehicles and modifications.Follow device prompt(s) to cycle the key to the ON/OFF position to complete loading your custom tuneĪlso here is a video from SCT showing this process as well.SCT X4 Flash Tuner with Pre-loaded Tunes for FORD The tuner will write the custom tune to the PCM and count up to 100%ĩ. The tuner will unlock the PCM and save the stock tune to the device and count up to 100%Ĩ. (WARNING – TURNING THE KEY OFF OR UNPLUGGING THE DEVICE WILL RESULT IN A BLANK PCM/TUNER)ħ. If it asks you to turn the key on again and it is already on, please ignore and leave as is. Follow device prompt(s) to cycle the key to the ON position. NOTE: If prompted to “Adjust Options”, skip this step if this is the first time loading a custom tune to the vehicle.Ħ.
Sct flash tuner update#
YOU WILL GET A GENERAL ERROR 110AE, WHICH REQUIRES AN ADDITIONAL UPDATE TO BE PERFORMED BEFORE FLASHING SPECIAL NOTE FOR 2015+ OWNERS - GENERAL ERROR 110AEĪFTER YOUR TUNER HAS BEEN UPDATED,YOU MUST PLUG IT INTO THE VEHICLE FOR THE DEVICE TO RECOGNIZE YOU ARE TRYING TO FLASH A 2015+. Choose your desired tune from the main menu and click Continue to acknowledge that the pre-loaded will be disabled (This may give a Vehicle Un-Supported Error under the Pre-Loaded tunes heading for some model years) When prompted to turn ON/OFF the ignition, please press the Engine Start button once with your foot off the clutch and/or brake pedal to avoid starting the vehicle.ĥ. NOTE: All 2015 Mustangs come equipped with engine start buttons as opposed to an ignition key. Follow the device prompt to cycle the key to the ON position to setup the device for flashing Press “Continue” to accept the disclaimerĤ. If it does, Demo Mode needs to be disabled from the Device Settings Menu.ģ. Ensure this does not say "MAIN MENU DEMO". Select “Program Vehicle” from the Main Menu. Plug the BAMA X4 into the OBDII port of your car.Ģ. Additionally, it is suggested to put a battery charger on the vehicle during the flash process to maintain adequate battery voltage.ġ. Make sure the ignition key is turned OFF before you connect your device to the vehicle. Also be sure to turn-off the vehicle's stereo and HVAC system.
Sct flash tuner manual#
To disable these functions, consult your vehicle’s owner’s manual and remove the fuse for each of these systems. It is always a good idea to turn-off any vehicle systems that may become active during the tuning process such as cooling fans, fuel pumps, etc. If you do have adjustible options, even changed options in our custom tune files will show up as "Stock" You can always contact us to turn these on. Do not worry if you do not have this option. Not all Bama Custom tunes come with Adjustible Options. YOU WILL GET A GENERAL ERROR 110AE, WHICH REQUIRES AN ADDITIONAL UPDATE TO BE PERFORMED BEFORE FLASHINGĤ. AFTER YOUR TUNER HAS BEEN UPDATED,YOU MUST PLUG IT INTO THE VEHICLE FOR THE DEVICE TO RECOGNIZE YOU ARE TRYING TO FLASH A 2015+. SPECIAL NOTE FOR 2015+ OWNERS - "GENERAL ERROR 110AE" WHEN TRYING TO LOAD TUNES. THE NEW VEHICLE WOULD NEED NEW TUNES AND ENROLLMENT INTO OUR PROGRAM.ģ.
DOING THIS WILL ALLOW THE TUNER TO THEN BE USED ON ANOTHER VEHICLE. BY LOADING TUNE FILES TO YOUR VEHICLE THIS WILL MARRY THE DEVICE TO YOUR VEHICLE AND WOULD NEED TO BE SET BACK TO ITS STOCK TUNE TO UN-MARRY THE TUNER FROM YOUR CAR. WHEN PROGRAMMING YOU WILL GET A WARNING THAT PRELOAD TUNES MAY BE DISABLED – THIS IS NORMAL - PLEASE CONTINUE TO LOAD YOUR BAMA CUSTOM TUNESĢ. THE FIRST TIME YOU ARE LOADING YOUR TUNES DO NOT CLICK ON “PRELOADED TUNES” AS.
0 kommentar(er)
